FORK TOOLS

SHOCK TOOLS

SPECIALTY TOOLS

BPF 45-49mm CAP WRENCH

This wrench along with the TFCH 06 were designed specifically for the B.P.F. (Big Piston Fork). A must have for the disassembly and reassembley of the 41/43mm BPF forks. Fits 09 GSXR1000 and 09 ZX-6R.
TFCW 4549

NEW SHOCK SPRING COMPRESSOR TOOL

The TSSC 02 Shock Spring Compressor is strong, light weight, and easy to use.  All that is required to remove the shock spring is a 19mm wrench.   The tool comes with 4 adapters (60, 66, 72, and 75mm) for different size spring collars and both an eyelet and clevis adapter.  Invented by Jason Eldredge of Corporate Suspension in Utah, this one is so cool you’ll want to remove shock springs just for the fun of it. More Info

NITROGEN GAUGE

The Nitrogen Gauge TSNG 01 does not require a wrench and easily reaches those hard to get recessed valve stems without an extension. It comes with a 1/4" flare nut quick coupling to work perfectly with the Regulator (TSNR 01) and Quick Connect Hose (TSNH 48).

BPF SEAL HEAD REMOVAL TOOL

This very special tool was made to remove the seal head assembly from the lower fork tube in 41/43mm BPF.
TFCH 06

SHOCK SPRING COMPRESSOR

Provides easy removal and installation of most shock springs with spring rates of 8 kg/mm or less without touching the spring collars. Features safety shaft locking device. TSSC 01

WP SHOCK NITROGEN RECHARGING TOOL

The Race Tech WP Nitrogen Charging Tool works on all WP shocks with a reservoir. It is really quick and easy to use as it clamps on to the reservoir. If you work on a lot of WP shocks this one is a must. TSNC 01

SEAL DRIVERS

Fork seal drivers for inverted and conventional forks. Many Seal Driver sizes available. TFSD Series. Selecting proper seal driver details.

SHOCK PRELOAD ADJUSTING TOOL

Are you tired of chewing up your rear shock spring collars when you adjust preload? Well then we've got the tool for you! Can be used aggressively on preload adjusting collars without damaging them. TSPA 01

WP NITROGEN FILL BOLT

The Nitrogen Valve Bolt is a simple replacement of the standard WP Nitrogen Bolt and allows pressurizing with a standard nitrogen needle (TSNN 01). The OEM WP Nitrogen filling system is pricey and cumbersome. SPNV 0512

CARTRIDGE HOLDING TOOL

Castle-style tools holds cartridge during disassembly. Part number
TFCH Series. Application Info

PIN SPANNERS

Pin Spanners have a unique design with a reverse taper on the pins. This helps them dig in so they don't pop out during use. 2 sizes: 4.0 / 4.5 and 5.0 / 5.5 mm. Pins are replaceable.

TMPS 01-PIN SPANNER 4.0 & 4.5mm
TMPS P01P-REPLACEMENT PINS 4.0 & 4.5 pair

TMPS 02-PIN SPANNER 5.0 & 5.5
TMPS P02P-REPLACEMENT PINS 5.0 & 5.5 pair

NITROGEN NEEDLE

This tool is designed for gas charged shocks with self-sealing type rubber valves. TSNN 01 (Used with Nitrogen Gauge - TSNG 02)

FORK CAP WRENCHES

We have fork cap wrenches for many different types of forks. Do a Product Search to find the Cap Wrench for your model. TFCW 243241H

SHOCK CLIP TOOL

Removes shock retaining clips without digging into the shock bodies. Made of hardened tool steel. If you work on shocks you'll really like this one!  TSCP 01

SHAFT HOLDING TOOLS

Holds fork damping rods, cartridges, shock shafts,etc. Unique design allows installation of dowels into the top of the vise jaws. The holding tools hang on the dowels instead of dropping on the ground when the vise is opened. Part Number Details

SEAL HEAD SETTING TOOL

Four sizes available. Mini's, Standard,Street and WP PDS shocks. Allows easy removal and installation of most shock seal head assemblies. Part Numbers  

RESERVOIR CAP REMOVAL TOOL

This tool screws onto the Schrader valve for easy removal of the bladder cap. (Simply screw the tool onto the Schrader valve and pull the bladder from the body.) TSCT 01

KYB 49mm FORK CAP WRENCH

Fits Yamaha R6. Enables loosening the fork caps without removing the handlebars. Steel construction for superior strength  TFCW 49

KTM WP 48mm FORK CAP WRENCH

Fits KTM WP 48 mm forks that require a special pin spanner wrench. Enables loosening the fork caps without removing the handlebars. TFCW 02

SAG MASTER

Voted as Dirt Bike Magazines 25 Best Tools Ever Invented, the Sag Master is a tool that makes measuring Static "Race" Sag a snap because you read it directly. No more subtracting! Check out the Sag Master in action.

Also useful in determining proper spring rates and monitoring linkage and seal drag. Comes with instructions and, doubles as a tape measure! TSSM 01

KTM WP 50mm FORK CAP WRENCH

Fits the newer style twin chamber WP forks with 50mm hex head cap. TFCW 50H

SHOWA 46/50 mm
TWIN CHAMBER CAP WRENCH

Multiple applications (46/50mm): HONDA CR250, CRF450, SUZUKI RM125/250. Removes compression valving assembly on most models. TFCW 4650

WP PDS SHOCK NEEDLE TOOL

Removes the Compression Needle from the shock body on early KTM WP PDS shocks. If you are only doing one shock this is the economical way to go. TSPS 1524

One of these is required if you are installing a SWCN 10 or 11  Telescopic Needle.

For later model PDS shocks see TSPS T Series Pin Spanners.

FORK CLICKER ADJUSTER TOOL

This Fork Compression Adjuster tool is flat with a tip on the bottom that easily fits between the handlebar and top of the fork tube. The tool is small, slim and easily fits into your pocket or tool bag. TFCA 01

FORK SPRING COMPRESSOR (wall mount)

This unique fork spring compressor is designed to work on most current sport bikes and road racers with cartridge forks. It allows the spring to be compressed while the fork cap is removed from the rod. This one is wall mounted and really fast.
TFSC 02

Best when used with Cartridge Bleed Tool (TFBT SET).

Recommended by Factory Harley for cartridge forks. TFSC A01 (H-D Adapter)

FORK SPRING COMPRESSOR (portable)

This portable version of the Fork Spring Compressor Tool. Can be used on or off the bike on many models. TFSC 01

WP PDS SHOCK NEEDLE T-HANDLE

This is the PRO version of the needle removal tool. If you are servicing a lot of WP PDS shocks this is the one to have. It is driven with a T-handle, holds the Needle, and is self-locating in the body. TSPS T Series

FORK BLEEDING TOOL

Unique self-starting design easily threads onto the damping rod. Baffled so the oil runs down the rod eliminating the typical mess. Available as a set. TFBT 02S

(Works great with the TFSC 01 Spring Compressor on street applications)

SHOCK SHAFT BUSHING DRIVER SET

Allows easy installation of shock shaft bushings into seal heads. The set comes with 12.5, 14, 16, and 18 mm drivers. TSBD SET

GRADUATED CYLINDER

Accurate measurement of fork oil for Twin Chamber forks. TFCG 500

CARTRIDGE ROD HOLDING TOOL

The Cartridge Rod Holding Tool allows you to more easily disassemble and assemble Showa Twin Chamber and most street cartridge forks. When applied, the tool holds back the spring allowing you to loosen or tighten the bottom nut or the fork cap on the cartridge rod. New plastic design keeps shafts from being marred. TFHP 01

ALUMINUM VISE JAWS

Race Tech Vise Jaws gently, yet firmly, hold fork tubes, fork legs and other round objects in a “V” down to a diameter of ½” (12.5 mm). The “V” is offset and overhangs the edge of the standard vise jaw to provide clearance on the post. Pre-drilled for the pins supplied with Race Tech’s shaft holding tools TFSH Series.

Made to fit 4 to 6.5” Craftsman vises with removable jaws. These vises have a bolt spacing of either 2.5 or 3 inches. Note: The Jaws fit other models and can be drilled to fit other makes of vises. TMVJ 065

FORK TUBE DISASSEMBLY TOOL

Removes and replaces fork tubes from fork bottoms (AKA axle clamps, fork lugs, etc.). TFTT 01

COMPRESSION ADJUSTER SOCKETS

These sockets are used to remove rear shock compression adjusters. Sizes available to fit most popular models. Part Numbers

Note: The punch marks at the threads must be drilled 1 mm deep prior to removal.

DEBURRING TOOL

Removes burrs resulting from grinding away factory peening during Fork Gold Valve installation. TMBD 08

17/19/22/24mm HEX AXLE TOOL

A.K.A. Big old allen wrench. Fits many sport and dirt bikes. TFHD 1724

SHOCK SEAL "BULLET" TOOLS

Bullet Tools make seal head installation onto shafts quick and easy. Practically eliminates the possibility of seal damage when installing the seal head onto the shaft. A must for serious tuners.
Part Numbers

NITROGEN REGULATOR

This Nitrogen Regulator is excellent quality. It has output to 300 psi and comes with a 1/4" flare nut fitting to work perfectly with the Hose TSNH 48 and Gauge TSNG 02.
Nitrogen Regulator TSNR 01

PRO OIL LEVEL TOOL

Collapsible tube for easy two handed use, not three hands! TFOL 02.

FORK PRELOAD ADJUSTING SOCKETS

Stop rounding off the edges of your adjusters. This tool allows you to perform easy fork preload changes. Specially designed for fork preload adjuster size and shape.
TFPA 14
TFPA 17

FORK REBOUND PISTON RING COMPRESSOR-WP

This tool is a must for WP Dual Chamber pressurized forks. It compresses the rebound piston ring for installation. TFPC 2328

SWINGARM PIVOT NUT TOOL

Made of hardened steel. Fits Suzuki SV650/1000, DL650/1000 and GSX-R750/1000/1100 TCPN 4301

FORK SEAL INSTALLATION SLEEVES

This special tool (thick plastic bag) prevents the oil seal from being torn during installation as it pass over the very sharp bearing race. Easy to use and prevents ripped seals. TFSB 01